arduino · jhansson-ard · Feb 20, 2024 · Feb 20, 2024
diff --git a/content/retired/01.boards/arduino-101-619/content.md b/content/retired/01.boards/arduino-101-619/content.md
@@ -7,8 +7,6 @@ sku: "ABX00005"
 source: "https://store.arduino.cc/arduino-101-619"
 ---
 
-***Note: This page refers to a product that is retired.***
-
 ![The Arduino 101 board](./assets/ABX00005_featured_2.jpg)
 
 A learning and development board that delivers the performance and low-power consumption of the [Intel® Curie™](/resources/datasheets/intel-curie-module-datasheet.pdf) Module with the simplicity of Arduino at an entry-level price. It keeps the same robust form factor and peripheral list of the UNO with the addition of onboard Bluetooth® Low Energy capabilities and a 6-axis accelerometer/gyro to help you easily expand your creativity into the connected world. 

diff --git a/content/retired/01.boards/arduino-BT-v1/content.md b/content/retired/01.boards/arduino-BT-v1/content.md
@@ -3,8 +3,6 @@ title: "Arduino BT v1"
 source: "https://arduino.cc/en/Main/ArduinoBoardBluetoothNew"
 ---
 
-***Note: This page refers to a product that is retired.***
-
 ## Arduino BT (Bluetooth®)
 
 ![](assets/ArduinoBT400.jpg)

diff --git a/content/retired/01.boards/arduino-BT/content.md b/content/retired/01.boards/arduino-BT/content.md
@@ -3,8 +3,6 @@ title: "Arduino BT (Bluetooth)"
 source: "https://arduino.cc/en/Main/ArduinoBoardBT"
 ---
 
-***Note: This page refers to a product that is retired.***
-
 ## Arduino BT (Bluetooth)
 
 ![Arduino BT Front](assets/ArduinoBT_Front_400px.jpg)

diff --git a/content/retired/01.boards/arduino-diecimila/content.md b/content/retired/01.boards/arduino-diecimila/content.md
diff --git a/content/retired/01.boards/arduino-duemilanove/content.md b/content/retired/01.boards/arduino-duemilanove/content.md
@@ -3,8 +3,6 @@ title: "Arduino Duemilanove"
 source: "https://arduino.cc/en/Main/ArduinoBoardDuemilanove"
 ---
 
-***Note: This page refers to a product that is retired.***
-
 ## Arduino Duemilanove
 
 ![](assets/ArduinoDuemilanove.jpg)

diff --git a/content/retired/01.boards/arduino-esplora/content.md b/content/retired/01.boards/arduino-esplora/content.md
@@ -7,8 +7,6 @@ sku: "A000095"
 source: "https://store.arduino.cc/arduino-esplora"
 ---
 
-***Note: This page refers to a product that is retired.***
-
 ![The Arduino Esplora board](./assets/A000095_top_2.jpg)
 
 The **Arduino Esplora** is a microcontroller board derived from the [Arduino Leonardo](https://www.arduino.cc/en/Guide/ArduinoLeonardo). The Esplora differs from all preceding Arduino boards in that it provides a number of built-in, ready-to-use set of onboard sensors for interaction. It's designed for people who want to get up and running with Arduino without having to learn about the electronics first. For a step-by-step introduction to the Esplora, check out the [Getting Started with Esplora](https://www.arduino.cc/en/Guide/ArduinoEsplora) guide.

diff --git a/content/retired/01.boards/arduino-ethernet-rev3-with-poe/content.md b/content/retired/01.boards/arduino-ethernet-rev3-with-poe/content.md
@@ -6,8 +6,6 @@ sku: "A000074"
 source: "https://store.arduino.cc/arduino-ethernet-rev3-with-poe"
 ---
 
-***Note: This page refers to a product that is retired.***
-
 ![The Arduino Ethernet Rev3 with PoE](./assets/a000074_front.jpg)
 
 The **Arduino Ethernet** is a microcontroller board based on the ATmega328P. It has 14 digital input/output pins, 6 analog inputs, a 16 MHz crystal oscillator, a RJ45 connection, a power jack, an ICSP header, and a reset button.

diff --git a/content/retired/01.boards/arduino-ethernet-rev3-without-poe/content.md b/content/retired/01.boards/arduino-ethernet-rev3-without-poe/content.md
@@ -6,8 +6,6 @@ sku: "A000068"
 source: "https://store.arduino.cc/arduino-ethernet-rev3-without-poe"
 ---
 
-***Note: This page refers to a product that is retired.***
-
 ![The Arduino Ethernet Rev3 without PoE](assets/a000068_front.jpg)
 
 The **Arduino Ethernet** is a microcontroller board based on the ATmega328\. It has 14 digital input/output pins, 6 analog inputs, a 16 MHz crystal oscillator, a RJ45 connection, a power jack, an ICSP header, and a reset button.

diff --git a/content/retired/01.boards/arduino-fio/content.md b/content/retired/01.boards/arduino-fio/content.md
@@ -3,8 +3,6 @@ title: Arduino Fio
 source: https://www.arduino.cc/en/Main/ArduinoBoardFio
 ---
 
-***Note: This page refers to a product that is retired.***
-
 ![The Arduino Fio board.](./assets/ArduinoFio.jpg)
 
 ## Overview

diff --git a/content/retired/01.boards/arduino-gemma/content.md b/content/retired/01.boards/arduino-gemma/content.md
@@ -7,8 +7,6 @@ sku: "ABX00001"
 source: "https://store.arduino.cc/arduino-gemma"
 ---
 
-***Note: This page refers to a product that is retired.***
-
 ![The Arduino Gemma board](assets/abx00001_front.jpg)
 
 The **Arduino Gemma** is a microcontroller board made by [Adafruit](https://www.adafruit.com/) based on the [ATtiny85](http://www.atmel.com/assets/atmel-2586-avr-8-bit-microcontroller-attiny25-attiny45-attiny85_datasheet.pdf). It has 3 digital input/output pins (of which 2 can be used as PWM outputs and 1 as analog input), an 8 MHz resonator, a micro USB connection, a JST connector for a 3.7V battery, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a battery to get started.

diff --git a/content/retired/01.boards/arduino-industrial-101/content.md b/content/retired/01.boards/arduino-industrial-101/content.md
diff --git a/content/retired/01.boards/arduino-isp/content.md b/content/retired/01.boards/arduino-isp/content.md
@@ -1,70 +1,68 @@
----
-title: "Arduino ISP"
-description: "The Arduino ISP is a tool to directly program your microcontroller through the ICSP connector."
-url_guide: "https://www.arduino.cc/en/Main.ArduinoISP"
-coverImage: "assets/A000092_last_featured_2.jpg"
-sku: "A000092"
-source: "https://store.arduino.cc/arduino-isp"
----
-
-***Note: This page refers to a product that is retired.***
-
-![The Arduino ISP board](assets/A000092_last_featured_2.jpg)
-
-The **Arduino ISP** is a tiny AVR-ISP (in-system programmer) based on David Mellis' project FabISP([http://fab.cba.mit.edu/content/projects/fabisp/](http://fab.cba.mit.edu/content/archive/projects/fabisp/)). With this programmer you can upload sketches and burn the bootloader on any AVR based boards, including Arduinos. By uploading a sketch with an external programmer you can remove the bootloader and use the extra space for your sketch. The Arduino ISP can also be used to burn the Arduino bootloader, so you can recover your chip if you accidentally corrupt the bootloader. Burning the bootloader is also necessary when you use a new ATmega microcontroller in your Arduino, and you wish to use the bootloader to upload a sketch via the USB-Serial connection.
-
-You can find [here](https://www.arduino.cc/en/Main/warranty) your board warranty information.
-
-## Getting Started
-
-You can find in the [Getting Started section](https://www.arduino.cc/en/Guide/HomePage) all the information you need to configure your board, use the Arduino So ftware (IDE), and start tinker with coding and electronics.
-
-### Need Help?
-
-* On the Software [on the Arduino Forum](https://forum.arduino.cc/index.php?board=63.0)
-* On Projects [on the Arduino Forum](https://forum.arduino.cc/index.php?board=3.0)
-* On the Product itself through [our Customer Support](https://support.arduino.cc/hc)
-
-## Documentation
-
-### OSH: Schematics
-
-Arduino ISP is open-source hardware! You can build your own board using the following files:
-
-[EAGLE FILES IN .ZIP](https://content.arduino.cc/assets/arduino-isp-reference-design.zip) 
-
-[SCHEMATICS IN .PDF](https://content.arduino.cc/assets/arduino-isp-schematic.pdf) 
-
-[WINDOWS DRIVERS](https://www.arduino.cc/en/uploads/Main/ArduinoISP_WindowsDrivers.zip)
-
-### How to use
-
-Connect the Arduino ISP to your Arduino board's ICSP headers. Make sure to match the orientation of the plugs by looking at the white dot on the corner of the connector. Once connected, open the Arduino IDE and select "Arduino ISP" under the *"Tools > Programmers"*menu. To upload a sketch using the Arduino ISP, choose *"Upload using programmer"* option in the*File* menu, or use the keyboard shortcut: *"CTRL+SHIFT+U"*. If you want to burn the bootloader into the AVR microcontroller select the "Burn bootloader" option under the *"Tools"* menu.
-
-**Note:** The Arduino ISP is only supported by Arduino IDE 1.5.7 or later.  
-
-For more details about using the Arduino ISP please visit the [Getting Started](https://www.arduino.cc/en/Guide/ArduinoISP) page
-
-### Tutorials 
-
-* [Using an Arduino as an AVR ISP](https://www.arduino.cc/en/Tutorial/ArduinoISP): how to use an Arduino board as an AVR ISP (in-system programmer). This allows you to use the board to burn the bootloader onto an AVR (e.g. theATmega168 or ATmega328 used in Arduino).
-* [Programming an ATtiny with Arduino ISP](http://scuola.arduino.cc/courses/lessons/cover/qX1117g): How to install the ATtiny core for the Arduino IDE for programming AVR ATtiny microcontrollers using the Arduino software and the Arduino ISP programmer.
-* [How to read your Arduino built-in EEPROM](http://scuola.arduino.cc/courses/lessons/view/B7PlK61): How to read the content of the onboard EEPROM on an AVR microcontroller by dumping the flash memory using the Arduino ISP programmer.
-
-### Powering the target board
-
-The Arduino ISP is able to provide the 5V power supply voltage to the board being programmed. If you want to power the board through the ISP you have to close the SJVCC jumper on the board.
-
-### Reprogramming the on board ATtiny44
-
-The firmware on the ATtiny44 inside the Arduino ISP can be updated or replaced. To program theATtiny you have to close the SJFAB jumper and connect an ISP programmer in the ICSP connector.
-
-### Troubleshooting
-
-**Verification error problem**
-
-If you encounter this kind of problem you should power the board you are trying to program with the Arduino ISP with external power rather than with USB power. For example if you are burning the bootloader to an Arduino Leonardo you have to power the Leonardo through the power jack with a 9V wall wart power supply.
-
-**Unknown USB device**
-
+---
+title: "Arduino ISP"
+description: "The Arduino ISP is a tool to directly program your microcontroller through the ICSP connector."
+url_guide: "https://www.arduino.cc/en/Main.ArduinoISP"
+coverImage: "assets/A000092_last_featured_2.jpg"
+sku: "A000092"
+source: "https://store.arduino.cc/arduino-isp"
+---
+
+![The Arduino ISP board](assets/A000092_last_featured_2.jpg)
+
+The **Arduino ISP** is a tiny AVR-ISP (in-system programmer) based on David Mellis' project FabISP([http://fab.cba.mit.edu/content/projects/fabisp/](http://fab.cba.mit.edu/content/archive/projects/fabisp/)). With this programmer you can upload sketches and burn the bootloader on any AVR based boards, including Arduinos. By uploading a sketch with an external programmer you can remove the bootloader and use the extra space for your sketch. The Arduino ISP can also be used to burn the Arduino bootloader, so you can recover your chip if you accidentally corrupt the bootloader. Burning the bootloader is also necessary when you use a new ATmega microcontroller in your Arduino, and you wish to use the bootloader to upload a sketch via the USB-Serial connection.
+
+You can find [here](https://www.arduino.cc/en/Main/warranty) your board warranty information.
+
+## Getting Started
+
+You can find in the [Getting Started section](https://www.arduino.cc/en/Guide/HomePage) all the information you need to configure your board, use the Arduino So ftware (IDE), and start tinker with coding and electronics.
+
+### Need Help?
+
+* On the Software [on the Arduino Forum](https://forum.arduino.cc/index.php?board=63.0)
+* On Projects [on the Arduino Forum](https://forum.arduino.cc/index.php?board=3.0)
+* On the Product itself through [our Customer Support](https://support.arduino.cc/hc)
+
+## Documentation
+
+### OSH: Schematics
+
+Arduino ISP is open-source hardware! You can build your own board using the following files:
+
+[EAGLE FILES IN .ZIP](https://content.arduino.cc/assets/arduino-isp-reference-design.zip) 
+
+[SCHEMATICS IN .PDF](https://content.arduino.cc/assets/arduino-isp-schematic.pdf) 
+
+[WINDOWS DRIVERS](https://www.arduino.cc/en/uploads/Main/ArduinoISP_WindowsDrivers.zip)
+
+### How to use
+
+Connect the Arduino ISP to your Arduino board's ICSP headers. Make sure to match the orientation of the plugs by looking at the white dot on the corner of the connector. Once connected, open the Arduino IDE and select "Arduino ISP" under the *"Tools > Programmers"*menu. To upload a sketch using the Arduino ISP, choose *"Upload using programmer"* option in the*File* menu, or use the keyboard shortcut: *"CTRL+SHIFT+U"*. If you want to burn the bootloader into the AVR microcontroller select the "Burn bootloader" option under the *"Tools"* menu.
+
+**Note:** The Arduino ISP is only supported by Arduino IDE 1.5.7 or later.  
+
+For more details about using the Arduino ISP please visit the [Getting Started](https://www.arduino.cc/en/Guide/ArduinoISP) page
+
+### Tutorials 
+
+* [Using an Arduino as an AVR ISP](https://www.arduino.cc/en/Tutorial/ArduinoISP): how to use an Arduino board as an AVR ISP (in-system programmer). This allows you to use the board to burn the bootloader onto an AVR (e.g. theATmega168 or ATmega328 used in Arduino).
+* [Programming an ATtiny with Arduino ISP](http://scuola.arduino.cc/courses/lessons/cover/qX1117g): How to install the ATtiny core for the Arduino IDE for programming AVR ATtiny microcontrollers using the Arduino software and the Arduino ISP programmer.
+* [How to read your Arduino built-in EEPROM](http://scuola.arduino.cc/courses/lessons/view/B7PlK61): How to read the content of the onboard EEPROM on an AVR microcontroller by dumping the flash memory using the Arduino ISP programmer.
+
+### Powering the target board
+
+The Arduino ISP is able to provide the 5V power supply voltage to the board being programmed. If you want to power the board through the ISP you have to close the SJVCC jumper on the board.
+
+### Reprogramming the on board ATtiny44
+
+The firmware on the ATtiny44 inside the Arduino ISP can be updated or replaced. To program theATtiny you have to close the SJFAB jumper and connect an ISP programmer in the ICSP connector.
+
+### Troubleshooting
+
+**Verification error problem**
+
+If you encounter this kind of problem you should power the board you are trying to program with the Arduino ISP with external power rather than with USB power. For example if you are burning the bootloader to an Arduino Leonardo you have to power the Leonardo through the power jack with a 9V wall wart power supply.
+
+**Unknown USB device**
+
 If your computer does not recognize the device try a different USB port. Some particular USB ports cause problems during the communication, changing the USB port usually fixes the problem.
diff --git a/content/retired/01.boards/arduino-leonardo-eth-2-with-poe/content.md b/content/retired/01.boards/arduino-leonardo-eth-2-with-poe/content.md
@@ -1,23 +1,21 @@
----
-title: "Arduino Leonardo ETH 2 with PoE"
-description: "All the fun of a Leonardo, plus an Ethernet port to extend your project to the IoT world."
-coverImage: "assets/a000023_featured_1.jpg"
-sku: "A000023"
-source: "https://store.arduino.cc/arduino-leonardo-eth-2-with-poe"
----
-
-***Note: This page refers to a product that is retired.***
-
-![The Arduino Leonardo ETH with PoE](assets/a000023_iso.jpg)
-
-The Arduino Leonardo ETH is the Leonardo with a built-in ethernet controller (Wiznet 5500 controller with RJ45 connector). Optional PoE (Power over Ethernet)
-
-## Documentation
-
-### OSH: Schematics
-
-The Arduino Leonardo ETH is open-source hardware! You can build your own board using the following files (Please note that the schematics are revision 1):
-
-[EAGLE FILES IN .ZIP](https://content.arduino.cc/assets/LeonardoEth_V1.0.zip) 
-
+---
+title: "Arduino Leonardo ETH 2 with PoE"
+description: "All the fun of a Leonardo, plus an Ethernet port to extend your project to the IoT world."
+coverImage: "assets/a000023_featured_1.jpg"
+sku: "A000023"
+source: "https://store.arduino.cc/arduino-leonardo-eth-2-with-poe"
+---
+
+![The Arduino Leonardo ETH with PoE](assets/a000023_iso.jpg)
+
+The Arduino Leonardo ETH is the Leonardo with a built-in ethernet controller (Wiznet 5500 controller with RJ45 connector). Optional PoE (Power over Ethernet)
+
+## Documentation
+
+### OSH: Schematics
+
+The Arduino Leonardo ETH is open-source hardware! You can build your own board using the following files (Please note that the schematics are revision 1):
+
+[EAGLE FILES IN .ZIP](https://content.arduino.cc/assets/LeonardoEth_V1.0.zip) 
+
 [SCHEMATICS IN .PDF](https://content.arduino.cc/assets/LeonardoEth_V1.0_sch.pdf)